banner_page

MAX303EPE+

150ns, 100ns SPDT 35Ohm DUAL Analog Switches BREAK-BEFORE-MAKE 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX303EPE+
  • Package: 16-DIP (0.300, 7.62mm)
  • Datasheet: PDF
  • Stock: 698
  • Description: 150ns, 100ns SPDT 35Ohm DUAL Analog Switches BREAK-BEFORE-MAKE 16 Pins 500pA 15V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Package / Case 16-DIP (0.300, 7.62mm)
Surface Mount NO
Number of Pins 16
Operating Temperature -40°C~85°C TA
Published 1995
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 16
ECCN Code EAR99
Resistance 35Ohm
Terminal Finish Matte Tin (Sn)
Additional Feature ALSO OPERATE WITH 10V TO 30V SINGLE SUPPLY
Subcategory Multiplexer or Switches
Technology CMOS
Terminal Position DUAL
Terminal Form THROUGH-HOLE
Peak Reflow Temperature (Cel) 260
Number of Functions 2
Supply Voltage 15V
Output SEPARATE OUTPUT
Pin Count 16
Power Supplies 5+-15V
Number of Channels 1
Number of Circuits 2
Max Supply Voltage 30V
Min Supply Voltage 10V
Voltage - Supply, Single/Dual (±) 10V~30V ±4.5V~20V
Neg Supply Voltage-Nom (Vsup) -15V
Max Dual Supply Voltage 20V
On-State Resistance (Max) 35Ohm
Min Dual Supply Voltage 4.5V
Multiplexer/Demultiplexer Circuit 2:1
Off-state Isolation-Nom 72 dB
Current - Leakage (IS(off)) (Max) 500pA
Channel Capacitance (CS(off), CD(off)) 12pF 12pF
On-state Resistance Match-Nom 0.5Ohm
Switch Circuit SPDT
Switch Time (Ton, Toff) (Max) 150ns, 100ns
Charge Injection 10pC
Channel-to-Channel Matching (ΔRon) 500m Ω
Crosstalk -90dB @ 1MHz
Switching BREAK-BEFORE-MAKE
Switch-on Time-Max 150ns
Switch-off Time-Max 100ns
Length 19.175mm
Radiation Hardening No
RoHS Status ROHS3 Compliant

MAX303EPE+ Overview


The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). Multiplexer and demultiplexer circuits have a number 2:1. Extended operating temperature around -40°C~85°C TA. Totally, there are 16 terminations. The electronic part provides high-quality output because it has 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. 16 pins are injected to the electronic part body. Unlike digital switches, these are based on SPDT switching circuits. It consists of 2 circuits. It has an internal resistance of 35Ohm. For details about the functions of 16 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 30V. The lowest voltage fed to the electronic component should be 10V. Despite this switch device's dual supply capability, its voltage should not exceed 20V. You should attach at least 4.5V voltage if you are using dual power supply. There are SEPARATE OUTPUT outputs on this analog switch ic. There is also ALSO OPERATE WITH 10V TO 30V SINGLE SUPPLY to look out for in this electronic part.

MAX303EPE+ Features


1 Channels
Switch Circuit: SPDT
Additional Features: ALSO OPERATE WITH 10V TO 30V SINGLE SUPPLY

MAX303EPE+ Applications


There are a lot of Maxim Integrated MAX303EPE+ Analog Switches & Multiplexers ICs applications.

  • Optical Applications
  • Fault Tolerant Systems
  • Fiber In The Loop (FITL)
  • Precision instrumentation
  • Multi-Line E1 Interface Cards
  • Automatic test equipment
  • E1 Network Equipment
  • Wireless Local Loop
  • Isolation
  • Data Acquisition Systems

Write a review

Note: HTML is not translated!
    Bad           Good