MAX303ESE+
| Parameters | |
|---|---|
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX303 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 2 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 150 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
MAX303ESE+ Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. High reliability is ensured by the advanced packaging method Tube. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Increasing operating temperature to around -40°C~85°C TA. There are 16 terminations totally. A electrical component with 2 channels is capable of high-quality output. A 15V voltage supply should turn on and run the electronic component. As part of its design, the 16 series is equipped with this electronic component. A SPDT switching circuit is used for these analog switches. Look for analog switch ic variants by searching with MAX303. This digital multiplexer has 35Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 30V in normal situations. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 10V. Put voltage above 1μA on the multiplexer to cause damage. Despite this switch's dual supply capability, its voltage should not exceed 20V. If you are using dual power supplies, you should attach at least 4.5V. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
MAX303ESE+ Features
2 Channels
Switch Circuit: SPDT
MAX303ESE+ Applications
There are a lot of Maxim Integrated MAX303ESE+ Analog Switches & Multiplexers ICs applications.
- Digital access cross connects
- Relay replacements
- Avionics and Military Systems
- Precision instrumentation
- Ultrasound
- USB 1.1 signal switching circuits
- Remote wireless modules
- Battery Powered Systems
- Multiplexers
- Data Acquisition Systems
