MAX305CSE
| Parameters | |
|---|---|
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 150ns |
| Switch-off Time-Max | 100ns |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | ALSO OPERATE WITH 10V TO 30V SINGLE SUPPLY |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX305 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 5+-15V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
MAX305CSE Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). High reliability is ensured by the advanced packaging method Tube. Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 2:1. Operation at a temperature around 0°C~70°C TA. In total, there are 16 terminations. A electrical component with 2 channels is capable of high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. An injection of 16 pins is performed into the body of the electrical component. Based on DPST - NO switching circuits, these analog multiplexers work. It consists of 2 circuits. Try searching with MAX305 to find analog multiplexer variants. There is 35Ohm internal resistance in this digital multiplexer. For details about the functions of 16 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users should never supply a voltage higher than 30V to a switch device. The lowest voltage the electronic part should receive is 10V. For this switch, a dual supply voltage is feasible, but it must not exceed 20VA dual power supply should have at least 4.5V voltage attached. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. Additional features include: ALSO OPERATE WITH 10V TO 30V SINGLE SUPPLY.
MAX305CSE Features
2 Channels
Switch Circuit: DPST - NO
Additional Features: ALSO OPERATE WITH 10V TO 30V SINGLE SUPPLY
MAX305CSE Applications
There are a lot of Maxim Integrated MAX305CSE Analog Switches & Multiplexers ICs applications.
- Industrial
- Low-Voltage
- Digital access cross connects
- Power routing
- Video switching
- Medical
- High speed data transmission line cards
- Communications systems
- Audio and video signal routing
- SONET
