banner_page

MAX306CPI+

200ns, 150ns 100Ohm Analog Switches BREAK-BEFORE-MAKE MAX306 28 Pins 500pA 15V 28-DIP (0.600, 15.24mm)


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX306CPI+
  • Package: 28-DIP (0.600, 15.24mm)
  • Datasheet: PDF
  • Stock: 189
  • Description: 200ns, 150ns 100Ohm Analog Switches BREAK-BEFORE-MAKE MAX306 28 Pins 500pA 15V 28-DIP (0.600, 15.24mm)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Through Hole
Mounting Type Through Hole
Package / Case 28-DIP (0.600, 15.24mm)
Number of Pins 28
Operating Temperature 0°C~70°C TA
Packaging Tube
Published 2004
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 28
ECCN Code EAR99
Resistance 100Ohm
Terminal Finish Tin (Sn)
Max Power Dissipation 727mW
Technology CMOS
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 15V
Terminal Pitch 2.54mm
Time@Peak Reflow Temperature-Max (s) 30
Base Part Number MAX306
Pin Count 28
Operating Supply Voltage 28V
Number of Channels 16
Number of Circuits 1
Max Supply Voltage 30V
Min Supply Voltage 5V
Operating Supply Current 500μA
Nominal Supply Current 16μA
Propagation Delay 300 ns
Turn On Delay Time 600 ns
Logic Function Multiplexer
Voltage - Supply, Single/Dual (±) 5V~30V ±4.5V~20V
Supply Type Dual, Single
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 300 ns
Max Dual Supply Voltage 20V
On-State Resistance (Max) 100Ohm
Min Dual Supply Voltage 4.5V
Dual Supply Voltage 9V
Multiplexer/Demultiplexer Circuit 16:1
Off-state Isolation-Nom 69 dB
Current - Leakage (IS(off)) (Max) 500pA
Channel Capacitance (CS(off), CD(off)) 8pF 130pF
On-state Resistance Match-Nom 1.5Ohm
Switch Time (Ton, Toff) (Max) 200ns, 150ns
Charge Injection 2pC
Channel-to-Channel Matching (ΔRon) 1.5 Ω
Crosstalk -92dB @ 100kHz
Switching BREAK-BEFORE-MAKE
Switch-on Time-Max 200ns
Signal Current-Max 0.03A
Height 4.45mm
Length 37.34mm
Width 14.61mm
Radiation Hardening No
REACH SVHC Unknown
RoHS Status ROHS3 Compliant
Lead Free Lead Free

MAX306CPI+ Overview


Packed in 28-DIP (0.600, 15.24mm), the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Through Hole. There is 16:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around 0°C~70°C TA extended. Total terminations are 28. A electrical component with 16 channels is capable of high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. The electronic part body is injected with 28 pins. This multiplexer is composed of 1 circuits. Look for analog switch ic variants by searching with MAX306. A 100Ohm internal resistance characterizes this multiplexer. Datasheets for 28 pin functions are available upon request. In a normalsituation, users should not supply the switches with voltage higher than 30V. An effective Dual, Single supply digital multiplexer. It is recommended that the electrical component receives a voltage of 5V. 500μA current would be enough for this multiplexer to operate. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. The voltage should be at least 4.5V if you are using dual power supplies. 28V operating voltages are supported by the electronic component.

MAX306CPI+ Features


16 Channels
500μA Supply Current

MAX306CPI+ Applications


There are a lot of Maxim Integrated MAX306CPI+ Analog Switches & Multiplexers ICs applications.

  • HDTV
  • Central office
  • Audio and video routing
  • Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
  • Sample-and-hold systems
  • Routers
  • Cross Connects
  • ATM
  • Cell phones
  • Digital access cross connects

Write a review

Note: HTML is not translated!
    Bad           Good