MAX306CWI+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 28 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Max Power Dissipation | 1W |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX306 |
| Pin Count | 28 |
| Operating Supply Voltage | 28V |
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 500μA |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 69 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 130pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 200ns |
| Signal Current-Max | 0.03A |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX306CWI+T Overview
Packed in 28-SOIC (0.295, 7.50mm Width), the electronic component is convenient for shipping overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. Surface Mount is where this multiplexer is located. 16:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around 0°C~70°C TA. The total number of terminations is 28. A electrical component with 16 channels is capable of high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. A total of 28 pins are injected into the body of the electronic part. The multiplexer consists of 1 circuits. If you are looking for variants of the digital switch, trying search with MAX306. An switch multiplexer with 100Ohm internal resistance has a value of 100Ohm. Datasheets for functions of 28 pins are available. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. Analog switch ics with Dual, Single supply type are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 5V. The switch device would be able to operate with 500μA current. Despite this switch's dual supply capability, its voltage should not exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. 28V operating voltages can be used with this electrical part.
MAX306CWI+T Features
16 Channels
500μA Supply Current
MAX306CWI+T Applications
There are a lot of Maxim Integrated MAX306CWI+T Analog Switches & Multiplexers ICs applications.
- Battery Powered Instruments
- Mechanical reed relay replacement
- Video signal routing
- Communication systems
- CSU
- PDH Multiplexers
- Communications systems
- Sample hold systems
- Routers
- Multiplexers
