MAX306EUI+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Max Power Dissipation | 1.025W |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX306 |
| Pin Count | 28 |
| Operating Supply Voltage | 28V |
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 500μA |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 69 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 130pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 200ns |
| Signal Current-Max | 0.03A |
| Length | 9.7mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX306EUI+ Overview
Due to its 28-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. In order to provide high reliability, an advanced packaging method Tube is used. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a number of circuits 16:1. The operating temperature is extended to around -40°C~85°C TA. There are 28 terminations totally. A electrical component with 16 channels is capable of high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. A key feature of the 28 series is the inclusion of this electronic part as part of its design. A total of 1 circuits make up this switch device. Look for analog switch ic variants by searching with MAX306. Analog switches have 175Ohm internal resistance. To find out what the functions of 28 pins are, please refer to their datasheets. Multiplexers should not be powered above 30V in normal situations. Dual, Single supply type digital switch with a low cost. In order for the electronic part to function properly, the lowest voltage should be 5V. It would be sufficient to run this analogue multiplexer with 500μA current. Despite this switch device's dual supply capability, its voltage should not exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. The electrical part can be operated at 28V voltage levels.
MAX306EUI+ Features
16 Channels
500μA Supply Current
MAX306EUI+ Applications
There are a lot of Maxim Integrated MAX306EUI+ Analog Switches & Multiplexers ICs applications.
- Video signal routing
- Channelized and Unchannelized DS3 applications
- CSU
- Voice over IP/DSL – Integrated Access Devices, Smart
- Channel Banks
- Ultrasound
- Cable PC
- SONET/SDH ADM
- Video switching
- Sample hold systems
