MAX306EUI+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 1.025W |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX306 |
| Pin Count | 28 |
| Operating Supply Voltage | 28V |
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 75μA |
| Propagation Delay | 450 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 69 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 130pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 200ns |
| Signal Current-Max | 0.03A |
| Length | 9.7mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX306EUI+T Overview
Presented in 28-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. 16:1 is the ratio of multiplexer to demultiplexer circuits. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 28. Due to its 16 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. It is injected into the electrical part body with 28 pins. A 1 circuit is present in this switch device. Use MAX306 to search for variants of the digital switches. As far as internal resistance is concerned, it has 100Ohm. For details about the functions of 28 pins, please refer to the datasheets. Users shouldn't supply more than 30V voltage to the switch device. Analog switch ics with Dual, Single supply type are cost-effective. There should be 5V voltage fed to the electrical part below 5V. 75μA current would be enough for this multiplexer to operate. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. When using dual power supplies, you should attach at least 4.5V. 28V operating voltages are supported by the electronic component.
MAX306EUI+T Features
16 Channels
75μA Supply Current
MAX306EUI+T Applications
There are a lot of Maxim Integrated MAX306EUI+T Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- Imaging
- SDH/SONET multiplexers
- USB 1.1 signal switching circuits
- Fault Tolerant Systems
- Cellular phones
- Signal routing between systems
- High speed data transmission line cards
- Sample hold systems
- Channel Banks
