MAX306EWI+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Max Power Dissipation | 1W |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX306 |
| Pin Count | 28 |
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 500μA |
| Nominal Supply Current | 75μA |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 69 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 130pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 200ns |
| Signal Current-Max | 0.03A |
| Height | 2.35mm |
| Length | 18.1mm |
| Width | 7.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX306EWI+ Overview
The electrical component comes in 28-SOIC (0.295, 7.50mm Width) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. 16:1 is the number of circuits in the multiplexer and demultiplexer. Extended operating temperature around -40°C~85°C TA. Total terminations are 28. A 16 channel electronic part produces high-quality output. Turning on and running the electrical part should be easy with a 15V voltage supply. A total of 28 pins are injected into the body of the electronic part. Circuits number 1 make up this analogue multiplexer. If you are looking for variants of the digital switch, trying search with MAX306. It has an internal resistance of 100Ohm. For functions related to 28 pins, please refer to the datasheets. It is generally not recommended to supply a voltage higher than 30V to the switch device in normal circumstances. An effective Dual, Single supply digital multiplexer. In order for the electronic part to function properly, the lowest voltage should be 5V. This multiplexer would work with 500μA current. For this switch, a dual supply voltage is feasible, but it must not exceed 20VIt is recommended that you attach at least 4.5V to your dual power supply.
MAX306EWI+ Features
16 Channels
500μA Supply Current
MAX306EWI+ Applications
There are a lot of Maxim Integrated MAX306EWI+ Analog Switches & Multiplexers ICs applications.
- Relay Replacement
- Medical systems
- E1 Network Equipment
- Intelligent PBX
- Sample hold systems
- Audio and video routing
- Communication systems
- Precision data acquisition
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Audio signal routing
