MAX306EWI+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | TIN |
| Max Power Dissipation | 1W |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX306 |
| Pin Count | 28 |
| Operating Supply Voltage | 28V |
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 500μA |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 69 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 130pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 200ns |
| Signal Current-Max | 0.03A |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX306EWI+T Overview
The electronic component is convenient to ship overseas because it is packed in a 28-SOIC (0.295, 7.50mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a number of circuits 16:1. Temperatures around -40°C~85°C TA are extended for operation. In total, 28 terminations have occurred. By its 16 channels, the electronic component provides high-quality output. A 15V voltage supply should turn on and run the electronic component. A total of 28 pins are injected into the body of the electronic part. It consists of 1 circuits. Use MAX306 to search for variants of the digital switches. A 175Ohm internal resistance characterizes this multiplexer. Datasheets for functions of 28 pins are available. It is generally not recommended to supply a voltage higher than 30V to the switch device in normal circumstances. Dual, Single supply type digital switch with a low cost. It is recommended to use 5V as the lowest voltage for the electrical part. The analogue multiplexer could operate on 500μA current. There is no problem with using dual supply voltage, but it should not exceed 20V. A dual power supply should have at least 4.5V voltage attached. There is a voltage range of 28V operating voltages for the electrical part.
MAX306EWI+T Features
16 Channels
500μA Supply Current
MAX306EWI+T Applications
There are a lot of Maxim Integrated MAX306EWI+T Analog Switches & Multiplexers ICs applications.
- Battery Powered Systems
- Mechanical reed relay replacement
- Cable Modem
- Private Branch Exchange (PBX)
- Automatic test equipment
- Video signal routing
- Multi-Line E1 Interface Cards
- FTTH
- Cell phones
- Intelligent PBX
