MAX3081EPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Tin (Sn) |
| HTS Code | 8542.39.00.01 |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX3081 |
| Pin Count | 8 |
| JESD-30 Code | R-PDIP-T8 |
| Qualification Status | Not Qualified |
| Power Supplies | 5V |
| Supply Current-Max | 1mA |
| Data Rate | 115Kbps |
| Output Characteristics | TOTEM-POLE |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Full |
| Receiver Hysteresis | 100mV |
| Interface Standard | EIA-422; EIA-485 |
| Receive Delay-Max | 200 ns |
| Transmit Delay-Max | 2600 ns |
| Output Low Current-Max | 0.004A |
| Out Swing-Min | 1.5 V |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX3081EPA+ Overview
Designed for common LEDs, this driver IC features an enhanced 8-DIP (0.300, 7.62mm) package.The package of this receiver is Tube.The Transceiver can transceiver type enables this part to be used in a wide range of applications.This wide receiver can be placed on any Through Hole-type PCB or development board.This differential driver requires a 4.75V~5.25V power supply.During operation, this electronic part may have up to 1/1 eligible receivers/drivers.For applications where the operating temperature is -40°C~85°C, this ic receiver was designed primarily.There is a voltage range of 5V for this line driver ic, so it can operate efficiently.For driving and receiving signals from data, this wide receiver has 8 terminations integrated.It is packaged with 8 pinouts that are market standard for this particular transceiver.Since the base part number MAX3081 uniquely identifies the product type, temperature, package, etc., you can use it to find more variations.This ic receiver provided a 1-bit resolution capability. In most cases, the receiver will be specified with a 1-bit resolution.A subcategory named Line Driver or Receivers can be used to group this rf transceiver module.Driver ICs are designed to work with a 5V power supply and this driver IC is one of them.It is recommended that enough current be supplied to the VCC pin of the ic receiver, but not more than 1mA.
MAX3081EPA+ Features
Tube package
8 pin count
5V power supply
MAX3081EPA+ Applications
There are a lot of Maxim Integrated MAX3081EPA+ Drivers/Receivers/Transceivers applications.
- Cable network front end
- Wireless interactive experience
- transmission relay
- Switching system
- Wireless smart house
- Indoor ad hoc meeting
- Servers
- interconnection between switches
- Sensor reporting
- Aircraft navigation
