MAX3082EESA+T
| Parameters | |
|---|---|
| Output Low Current-Max | 0.004A |
| Out Swing-Min | 2 V |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Subcategory | Line Driver or Receivers |
| Max Power Dissipation | 727mW |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX3082 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Interface | RS-422, RS-485 |
| Nominal Supply Current | 375μA |
| Data Rate | 115Kbps |
| Differential Output | YES |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 25mV |
| Number of Transceivers | 1 |
| ESD Protection | Yes |
| Receive Delay-Max | 200 ns |
| Simplex/Duplex | Half Duplex |
| Transmit Delay-Max | 2600 ns |
MAX3082EESA+T Overview
Designed for common LEDs, this driver IC features an enhanced 8-SOIC (0.154, 3.90mm Width) package.The Tape & Reel (TR) package houses this receiver.The Transceiver can transceiver type enables this part to be used in a wide range of applications.Ideally, you should place this wide receiver on a Surface Mount-type PCB or development board.Power supply requirements for this differential driver are 4.75V~5.25V.Up to 1/1 receivers/drivers can be installed simultaneously on this electronic part.This ic receiver has been primarily designed for applications where the operating temperature is -40°C~85°C.5V is the supply voltage range that this line driver ic can efficiently operate with.Wide receiver has 8 terminations built in for driving or receiving signals from data.It is packaged with 8 pinouts that are market standard for this particular transceiver.The base part number MAX3082 identifies the product type, temperature, package, etc., so you can search for more variants by using it.This is a 8-pin driver IC with enhanced power dissipation control.Through optical transceiver downsizing and high-density Surface Mount mounting technologies, its package size is reduced dramatically.It was possible to achieve a 1-bit resolution through this ic receiver.This receiver is typically specified with a resolution of 1 bits. As a result of the design of this transceiver module, the input voltage supply is designed to operate at 5V.3 volts.It is possible to subcategoriLine Driver or Receiverse this rf transceiver module as Line Driver or Receivers.The driver IC in this product is designed so that it can be powered by 5V.In total, there are 1 transceivers implemented by this module isolated transceiver.
MAX3082EESA+T Features
Tape & Reel (TR) package
8 pin count
8 pins
5V power supply
MAX3082EESA+T Applications
There are a lot of Maxim Integrated MAX3082EESA+T Drivers/Receivers/Transceivers applications.
- Wireless HD Photography
- Aircraft navigation
- Satellite communication
- Wireless projection application for conferences
- Routers
- Broadcast application
- Switches
- Home theater wiring-free
- Wireless teaching
- Gigabit Ethernet
