MAX3083EESD+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 259.19969mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Line Driver or Receivers |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX3083 |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Interface | RS-422, RS-485 |
| Operating Supply Current | 600μA |
| Data Rate | 500kbps |
| Differential Output | YES |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Full |
| Receiver Hysteresis | 100mV |
| Number of Transceivers | 1 |
| Receive Delay-Max | 200 ns |
| Simplex/Duplex | Full Duplex |
| Output Low Current-Max | 0.004A |
| Out Swing-Min | 2 V |
| Height | 1.5mm |
| Length | 8.75mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX3083EESD+ Overview
This LED driver IC features an enhanced 14-SOIC (0.154, 3.90mm Width) package for driving common LEDs.The package of this receiver is Tube.With its Transceiver can transceiver design, this part can be incorporated into a wide range of solutions.You can place this wide receiver to any Surface Mount-type PCB or development board.With respect to the power supply, this differential driver uses 4.75V~5.25V.As many as 1/1 receivers/drivers are eligible for use on this electronic part.IC receiver is designed for applications with a temperature of -40°C~85°C.Wide receiver can operate within the range of 5V supply voltages efficiently.This wide receiver has 14 terminations for driving and receiving data signals.It is packaged with 14 pinouts that are market standard for this particular transceiver.As the base part number MAX3083 identifies the product type, temperature, package, etc., you can try searching with it to get more variants of this part.It is a 14-pin driver IC with enhanced power dissipation controls.A dramatic reduction in package size is achieved through optical transceiver downsizing and high-density Surface Mount mounting technologies.It is important to note that this ic receiver had a maximum resolution of 1 bits.In most cases, the receiver will be specified with a 1-bit resolution.As mentioned above, the transceiver module is designed to operate from an input voltage supply of 5V.An additional subcategory named Line Driver or Receivers can be created for this rf transceiver module.The driver IC in this product is designed so that it can be powered by 5V.Regarding the number of transceiver this module isolated transceiver implements, there are 1 transceivers overall.There is no matter what the input voltage is. The integrating circuit is able to drive LEDs with an input voltage of 600μA.
MAX3083EESD+ Features
Tube package
14 pin count
14 pins
5V power supply
MAX3083EESD+ Applications
There are a lot of Maxim Integrated MAX3083EESD+ Drivers/Receivers/Transceivers applications.
- Ethernet circuitry
- Changeing the frequency from IF to RF
- Metro access rings
- Bar, KTV wireless entertainment
- Portable radio
- Precision engineering measurement
- Datacom networking applications
- IP cameras
- Tuner
- Satellite communications networks
