MAX3085EESA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Line Driver or Receivers |
| Max Power Dissipation | 727mW |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX3085 |
| Pin Count | 8 |
| Output Voltage | 13V |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Voltage | 5V |
| Interface | RS-422, RS-485 |
| Nominal Supply Current | 1mA |
| Data Rate | 500kbps |
| Differential Output | YES |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 100mV |
| Number of Transceivers | 1 |
| Receive Delay-Max | 200 ns |
| Simplex/Duplex | Half Duplex |
| Output Low Current-Max | 0.004A |
| Out Swing-Min | 2 V |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX3085EESA+T Overview
Due to the enhanced 8-SOIC (0.154, 3.90mm Width) package, this driver IC is excellent for driving common LEDs.The receiver is packaged in a Tape & Reel (TR) package.As a Transceiver can transceiver, this part has enabled many applications to be served.A Surface Mount-type PCB or development board can be used to place this wide receiver.This differential driver requires a 4.75V~5.25V power supply.During operation, this electronic part may have up to 1/1 eligible receivers/drivers.The operating temperature of this ic receiver is -40°C~85°C. It is primarily designed for applications with low temperatures.Driver ICs with a supply voltage range of 5V can operate efficiently.In order to drive and receive signals from data, this wide receiver has 8 terminations integrated.The pinouts for this transceiver are standardized to meet the needs of the market.The base part number MAX3085 identifies the product type, temperature, package, etc., so you can search for more variants by using it.Wide receiver with enhanced power dissipation control, 8-pin.As a result of optical transceiver downsizing and high-density Surface Mount mounting technologies, its package size has been greatly reduced.It was possible to achieve a 1-bit resolution through this ic receiver.There is typically a resolution of 1 bits specified with this receiver.As mentioned above, the transceiver module is designed to operate from an input voltage supply of 5V.A rf transceiver module named Line Driver or Receivers belongs to this subcategory.This driver IC is designed to operate from a 5V power supply.In total, there are 1 transceivers implemented by this module isolated transceiver.There is a capabilWide receivery to deliver voltage at 13V wWide receiverh this device.
MAX3085EESA+T Features
Tape & Reel (TR) package
8 pin count
8 pins
5V power supply
MAX3085EESA+T Applications
There are a lot of Maxim Integrated MAX3085EESA+T Drivers/Receivers/Transceivers applications.
- Single fiber bidirectional application
- Mainframes, workstations or storage devices
- Wireless network systems
- Wired telephone
- TV signal transmission
- Gigabit Ethernet
- Wireless teaching
- Switching system
- Low power, low voltage systems
- Wireless transmission
