MAX3088CSA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Line Driver or Receivers |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX3088 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Interface | RS-422, RS-485 |
| Operating Supply Current | 600μA |
| Data Rate | 10Mbps |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 100mV |
| Number of Transceivers | 1 |
| Simplex/Duplex | Half Duplex |
| Transmit Delay-Max | 60 ns |
| Output Low Current-Max | 0.004A |
| Out Swing-Min | 2 V |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX3088CSA+ Overview
LED drivers with the enhanced 8-SOIC (0.154, 3.90mm Width) package will be able to drive a variety of common LEDs with ease.There is a Tube package for this receiver.The Transceiver can transceiver type enables this part to be used in a wide range of applications.Any Surface Mount-type PCB or development board can be used with this wide receiver.A power supply of 4.75V~5.25V is used by this differential driver.As many as 1/1 eligible receivers/drivers can be used simultaneously with this electronic part.In most applications, this ic receiver is used in environments where 0°C~70°C is the operating temperature.An output voltage range of 5V is sufficient to run this line driver ic efficiently.8 terminations are integrated into this wide receiver for driving and receiving signals from data.The pinouts for this transceiver are standardized to meet the needs of the market.You can search with MAX3088 to get more variants of this part, since it identifies the product type, temperature, package, etc.8-pin driver IC with improved power dissipation control.Package size is drastically reduced by downsizing ICs and mounting them in high-density Surface Mount arrays.In this ic receiver, the resolution was able to be set to a maximum of 1 bits.As a rule of thumb, this receiver is typically specified with a resolution of 1 bits.An input voltage supply of 5V is required to operate the transceiver module.There is a subcategory called Line Driver or Receivers for this rf transceiver module.It is designed to be operated from a 5V power supply, so the module isolated transceiver will work effectively.ICs implement a total of 1 transceivers.It has the ability to drive LEDs with an input voltage of up to about 600μA with the help of this integrating circuit.
MAX3088CSA+ Features
Tube package
8 pin count
8 pins
5V power supply
MAX3088CSA+ Applications
There are a lot of Maxim Integrated MAX3088CSA+ Drivers/Receivers/Transceivers applications.
- Data center
- Wireless showroom
- Wireless projection application for business talks
- Transmission stations
- Servers
- Datacom networking applications
- Pocket PC
- Mainframes, workstations or storage devices
- Broadcast application
- Interconnection between switches and computers
