MAX3089EEPD+
| Parameters | |
|---|---|
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX3089 |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Nominal Supply Current | 600μA |
| Data Rate | 10Mbps |
| Differential Output | YES |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Full |
| Receiver Hysteresis | 100mV |
| Interface Standard | EIA-422; EIA-485 |
| Number of Transceivers | 1 |
| Receive Delay-Max | 200 ns |
| Transmit Delay-Max | 2600 ns |
| Output Low Current-Max | 0.004A |
| Out Swing-Min | 2 V |
| Height Seated (Max) | 4.572mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Line Driver or Receivers |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
MAX3089EEPD+ Overview
Designed for common LEDs, this driver IC features an enhanced 14-DIP (0.300, 7.62mm) package.Tube package is used to mount this receiver.Several solutions have used this Transceiver can transceiver in a variety of applications due to its Transceiver IC nature.A Through Hole-type PCB or development board can be used to place this wide receiver.It takes 4.75V~5.25V from the power supply to run this differential driver.It is possible to have up to 1/1 receivers/drivers in use simultaneously with this electronic part.For applications where the operating temperature is -40°C~85°C, this ic receiver was designed primarily.Driver ICs in this category can operate efficiently with a supply voltage range of 5V.The integrated terminations of this wide receiver allow it to drive and receive signals from data.In this package, you will find 14 market-standard pinouts for this transceiver.The base part number MAX3089 identifies the product type, temperature, package, etc., so you can search for more variants by using it.It is a 14-pin driver IC with enhanced power dissipation controls.Its package size is drastically reduced by downsizing ICs and utilizing high-density Through Hole mounting techniques.In this ic receiver, the resolution was able to be set to a maximum of 1 bits.There is typically a resolution of 1 bits specified with this receiver.As mentioned above, the transceiver module is designed to operate from an input voltage supply of 5V.This rf transceiver module can be grouped into a subcategory named Line Driver or Receivers.The driver IC in this product is designed so that it can be powered by 5V.Regarding the number of transceiver this module isolated transceiver implements, there are 1 transceivers overall.
MAX3089EEPD+ Features
Tube package
14 pin count
14 pins
5V power supply
MAX3089EEPD+ Applications
There are a lot of Maxim Integrated MAX3089EEPD+ Drivers/Receivers/Transceivers applications.
- Remote controls
- Bridges
- Bar, KTV wireless entertainment
- Telecom applications
- Satellite communications networks
- Ethernet circuitry
- Mainframes, workstations or storage devices
- Broadcast application
- Notebook
- Car radio
