MAX3089ESD+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| HTS Code | 8542.39.00.01 |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX3089 |
| Pin Count | 14 |
| JESD-30 Code | R-PDSO-G14 |
| Qualification Status | Not Qualified |
| Power Supplies | 5V |
| Supply Current-Max | 1mA |
| Data Rate | 10Mbps |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Full |
| Receiver Hysteresis | 100mV |
| Interface Standard | EIA-422; EIA-485 |
| Receive Delay-Max | 200 ns |
| Transmit Delay-Max | 1000 ns |
| Output Low Current-Max | 0.004A |
| Out Swing-Min | 1.5 V |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX3089ESD+T Overview
This driver chip is excellent for driving common LEDs due to its enhanced 14-SOIC (0.154, 3.90mm Width) package.The Tape & Reel (TR) package houses this receiver.With its Transceiver can transceiver design, this part can be incorporated into a wide range of solutions.On any Surface Mount-type PCB or development board, you can install this wide receiver.Power supply requirements for this differential driver are 4.75V~5.25V.Up to 1/1 receivers/drivers can be installed simultaneously on this electronic part.In most applications, this ic receiver is used in environments where -40°C~85°C is the operating temperature.Driver ICs in this category can operate efficiently with a supply voltage range of 5V.In order to drive and receive signals from data, this wide receiver has 14 terminations integrated.In this package, you will find 14 market-standard pinouts for this transceiver.Since the base part number MAX3089 describes the product type, temperature, package, etc., you might get more options by searching with it.There is a capability of 1-bit resolution with this ic receiver.In most cases, the receiver will be specified with a 1-bit resolution.It is possible to subcategoriLine Driver or Receiverse this rf transceiver module as Line Driver or Receivers.IC5V is a high performance driver IC designed to work with a 5V power supply.The VCC pin of the ic receiver should receive enough but not more than 1mA of input current.
MAX3089ESD+T Features
Tape & Reel (TR) package
14 pin count
5V power supply
MAX3089ESD+T Applications
There are a lot of Maxim Integrated MAX3089ESD+T Drivers/Receivers/Transceivers applications.
- Ethernet circuitry
- Satellite radio receiver
- Wireless 3D game
- Sensor reporting
- WDM transmission
- Wireless smart house
- Metro access rings
- Low power, low voltage systems
- Carrier phase observations
- Wireless security systems
