MAX308CPE
| Parameters | |
|---|---|
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 750pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 26pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Height | 4.45mm |
| Length | 19.43mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Contact Plating | Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX308 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 500μA |
| Nominal Supply Current | 75μA |
| Throw Configuration | DPST |
| Propagation Delay | 175 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 8:1 |
MAX308CPE Overview
This electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Through Hole. Multiplexers and demultiplexers have a number of circuits 8:1. Extended operating temperature around 0°C~70°C TA. There are 16 terminations totally. A 8 channel electronic part produces high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. A total of 16 pins are injected into the body of the electronic part. There are 1 circuits in this multiplexer. Use MAX308 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 100Ohm. You can find the functions of the 16 pins in the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. There should be 5V voltage fed to the electrical part below 5V. The analogue multiplexer could operate on 500μA current. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. If you are using a dual power supply, you should attach at least 5V. There is a voltage range of 28V operating voltages for the electrical part.
MAX308CPE Features
8 Channels
500μA Supply Current
MAX308CPE Applications
There are a lot of Maxim Integrated MAX308CPE Analog Switches & Multiplexers ICs applications.
- MP3 players
- Low-Voltage
- Cross Connects
- RGB switches
- Audio and video signal routing
- Industrial control systems
- PDH Multiplexers
- DSUs
- High speed data transmission line cards
- Cable PC
