MAX308CSE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX308 |
| Pin Count | 16 |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 500μA |
| Nominal Supply Current | 75μA |
| Throw Configuration | DPST |
| Propagation Delay | 175 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 9V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 750pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 26pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 100Ohm |
| Signal Current-Max | 0.03A |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX308CSE+ Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tube is used. In Surface Mount, this analog switch is mounted. 8:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around 0°C~70°C TA. Total terminations are 16. A high-quality output is provided by the electrical component's 8 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. There are 16 pins injected into the electronic part body. It consists of 1 circuits. If you are looking for variants of the digital switch, trying search with MAX308. There is 100Ohm internal resistance in this digital multiplexer. The functions of 16 pins can be found in the datasheets. Multiplexers should not be powered above 30V in normal situations. An effective Dual, Single supply digital multiplexer. 5V is the lowest voltage the electrical component should receive. It would be sufficient to run this analogue multiplexer with 500μA current. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. If you are using a dual power supply, you should attach at least 5V. Drain to Source resistance is 100Ohm.
MAX308CSE+ Features
8 Channels
500μA Supply Current
Drain-to-Source resistance: 100Ohm
MAX308CSE+ Applications
There are a lot of Maxim Integrated MAX308CSE+ Analog Switches & Multiplexers ICs applications.
- Public switching systems
- E1 Multiplexer
- PDAs
- Mechanical reed relay replacement
- Ultrasound
- Wireless Local Loop
- Industrial
- Imaging
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Residential Gateways, Home Gateway/Router
