MAX308CSE+T
| Parameters | |
|---|---|
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX308 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 500μA |
| Throw Configuration | DPST |
| Propagation Delay | 175 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 750pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 26pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
MAX308CSE+T Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. The ratio between the number of multiplexer and demultiplexer circuits is 8:1. Operating temperature around 0°C~70°C TA extended. The total number of terminations is 16. A 8 channel electronic part produces high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. There is an electrical component included in the 16 series. 1 circuits are used in this analogue multiplexer. Use MAX308 to search for variants of the digital switches. There is 100Ohm internal resistance in this digital multiplexer. You can find the functions of the 16 pins in the datasheets. normally, users should not supply switches with voltages higher than 30V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. The lowest voltage the electronic part should receive is 5V. It would be sufficient to run this analogue multiplexer with 500μA current. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. When using dual power supplies, you should attach at least 5V. Operating voltages of 28V are compatible with the electrical part.
MAX308CSE+T Features
8 Channels
500μA Supply Current
MAX308CSE+T Applications
There are a lot of Maxim Integrated MAX308CSE+T Analog Switches & Multiplexers ICs applications.
- Wireless Local Loop
- High speed data transmission line cards
- Data Acquisition Systems
- Digital Cross-Connects
- Remote Powered Equipment
- Medical systems
- Audio signal routing
- Signal routing between systems
- Mechanical reed relay replacement
- Avionics
