MAX308CUE+
| Parameters | |
|---|---|
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 457mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX308 |
| Pin Count | 16 |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 500μA |
| Nominal Supply Current | 16μA |
| Throw Configuration | DPST |
| Propagation Delay | 175 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 750pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 26pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e3 |
MAX308CUE+ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). High reliability is provided by advanced packaging method Tube. The multiplexer is located in Surface Mount. 8:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around 0°C~70°C TA extended. The total number of terminations is 16. This electronic part offers high-quality output due to its 8 channels. An 15V voltage supply should allow the electrical part to be turned on and run. A total of 16 pins are injected into the electrical part body. The circuits in this analogue multiplexer number 1. MAX308 can be used to search for analog multiplexer variants. An switch multiplexer with 100Ohm internal resistance has a value of 100Ohm. For details about the functions of 16 pins, please refer to the datasheets. normally, users should not supply switches with voltages higher than 30V. The analog switch ic is of the Dual, Single supply type and is cost-effective. It is recommended that the electrical component receives a voltage of 5V. 500μA current would be enough for this multiplexer to operate. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. If you are using dual power supplies, you should attach at least 5V.
MAX308CUE+ Features
8 Channels
500μA Supply Current
MAX308CUE+ Applications
There are a lot of Maxim Integrated MAX308CUE+ Analog Switches & Multiplexers ICs applications.
- USB 1.1 signal switching circuits
- Transmit
- E1 Network Equipment
- Avionics
- Mechanical reed relay replacement
- PCMCIA cards
- Voice over IP/DSL – Integrated Access Devices, Smart
- High reliability control systems
- High speed data transmission line cards
- Routers
