MAX308EPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX308 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 500μA |
| Throw Configuration | DPST |
| Propagation Delay | 175 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 750pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 26pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Height Seated (Max) | 4.572mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
MAX308EPE Overview
Shipping overseas is convenient with the electronic component packed in 16-DIP (0.300, 7.62mm). High reliability is achieved by using advanced packaging method Tube. Through Hole is where this multiplexer is located. Multiplexers and demultiplexers have a number of circuits 8:1. Extended operating temperature around -40°C~85°C TA. Total terminations are 16. As a result of its 8 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. An electrical component of this type can be found in the 16 series. The circuits in this analogue multiplexer number 1. Using the MAX308 search parameter, you can discover variants of the switch. The internal resistance of this digital multiplexer is 100Ohm. For details about the functions of 16 pins, please refer to the datasheets. It is generally not recommended to supply a voltage higher than 30V to the switch device in normal circumstances. Dual, Single supply type digital switch with a low cost. The lowest voltage the electronic part should receive is 5V. An operating current of 500μA would be sufficient for this switch device. For this switch, a dual supply voltage is feasible, but it must not exceed 20VA dual power supply should have at least 5V voltage attached. The electrical part can be operated at 28V voltage levels.
MAX308EPE Features
8 Channels
500μA Supply Current
MAX308EPE Applications
There are a lot of Maxim Integrated MAX308EPE Analog Switches & Multiplexers ICs applications.
- Relay Replacement
- PCMCIA cards
- Sample hold systems
- Avionics and Military Systems
- Microprocessor controlled systems
- Fiber In The Loop (FITL)
- Data switching
- Avionics test equipment
- Audio signal routing
- Video signal routing
