MAX308ESE+
| Parameters | |
|---|---|
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 16μA |
| Throw Configuration | DPST |
| Propagation Delay | 175 ns |
| Turn On Delay Time | 150 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 750pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 26pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX308 |
| Pin Count | 16 |
| Number of Channels | 8 |
| Number of Circuits | 1 |
MAX308ESE+ Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. High reliability is achieved by using advanced packaging method Tube. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 8:1. Operation at a temperature around -40°C~85°C TA. In total, there have been 16 terminations. The electronic part delivers high-quality output through its 8 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. There are 16 pins injected into the electronic part body. The multiplexer consists of 1 circuits. MAX308 can be used to search for analog multiplexer variants. Internally, this switch multiplexer has a resistance of 100Ohm. Datasheets for functions of 16 pins are available. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. Dual, Single supply type digital switch with a low cost. 5V is the lowest voltage the electrical component should receive. An operating current of 16μA would be sufficient for this switch device. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. A dual power supply should have at least 5V voltage attached.
MAX308ESE+ Features
8 Channels
16μA Supply Current
MAX308ESE+ Applications
There are a lot of Maxim Integrated MAX308ESE+ Analog Switches & Multiplexers ICs applications.
- Video switching
- SDH
- Access Concentrators
- Cell phones
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Fault Tolerant Systems
- Sample-and-hold systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Transmit
- High reliability control systems
