Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2002 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
100Ohm |
Terminal Finish |
Matte Tin (Sn) |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX309 |
Pin Count |
16 |
Operating Supply Voltage |
28V |
Number of Channels |
4 |
Number of Circuits |
2 |
Max Supply Voltage |
30V |
Min Supply Voltage |
5V |
Operating Supply Current |
500μA |
Nominal Supply Current |
75μA |
Throw Configuration |
4PST |
Propagation Delay |
175 ns |
Turn On Delay Time |
600 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
5V~30V ±5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
300 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
5V |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
750pA |
Channel Capacitance (CS(off), CD(off)) |
3pF 26pF |
On-state Resistance Match-Nom |
1.5Ohm |
Switch Circuit |
SP4T |
Switch Time (Ton, Toff) (Max) |
150ns, 150ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
1.5 Ω |
Crosstalk |
-92dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
150ns |
Switch-off Time-Max |
150ns |
Drain to Source Resistance |
100Ohm |
Signal Current-Max |
0.03A |
Height |
1.5mm |
Length |
10mm |
Width |
4mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MAX309CSE+ Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. Advanced packaging method Tube is used to provide high reliability. Mounted in Surface Mount is this multiplexer. There is 4:1 ratio between the number of multiplexers and demultiplexers. Operating temperature extended to 0°C~70°C TA. Totally, there are 16 terminations. A 4 channel electronic part produces high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. An injection of 16 pins is performed into the body of the electrical component. Based on SP4T switching circuits, these analog multiplexers work. Circuits number 2 make up this analogue multiplexer. Try searching for the analog switch ic with MAX309 if you are looking for variants. As far as internal resistance is concerned, it has 100Ohm. The functions of 16 pins can be found in the datasheets. In normalcircumstances, users should not exceed 30V volts for the multiplexer. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 5V is the lowest voltage that should be fed to the electronic electronic part. The switch device would be able to operate with 500μA current. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. With dual power supplies, you should attach at least 5V. This electrical part is compatible with 28V operating voltages. This electronic component presents a Drain to Source resistance of 100Ohm.
MAX309CSE+ Features
4 Channels
Switch Circuit: SP4T
500μA Supply Current
Drain-to-Source resistance: 100Ohm
MAX309CSE+ Applications
There are a lot of Maxim Integrated MAX309CSE+ Analog Switches & Multiplexers ICs applications.
- Video switching
- Remote wireless modules
- Cross Connects
- Industrial and process control systems
- DVD-R
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Battery Powered Instruments
- Automatic test equipment
- Imaging
- E1 Multiplexer