MAX309ESE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX309 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 500μA |
| Throw Configuration | 4PST |
| Propagation Delay | 175 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 750pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 26pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 150ns |
| Switch-off Time-Max | 150ns |
| Signal Current-Max | 0.03A |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX309ESE+ Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. To ensure high reliability, a new packaging method Tube is used. It is mounted in the position Surface Mount. 4:1 is the ratio between multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. In total, there are 16 terminations. By its 4 channels, the electronic component provides high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. An electrical component of this type can be found in the 16 series. Circuits based on SP4T switching are used to construct these analog switch ics. The circuits in this analogue multiplexer number 2. Try searching with MAX309 if you're looking for variants. There is 175Ohm internal resistance in this digital multiplexer. Please refer to the datasheets for 16 pins functions. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. Analog switch ics with Dual, Single supply type are cost-effective. It is recommended to use 5V as the lowest voltage for the electrical part. 500μA current would be enough for this multiplexer to operate. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. With dual power supplies, you should attach at least 5V. 28V operating voltages can be used with this electrical part.
MAX309ESE+ Features
4 Channels
Switch Circuit: SP4T
500μA Supply Current
MAX309ESE+ Applications
There are a lot of Maxim Integrated MAX309ESE+ Analog Switches & Multiplexers ICs applications.
- Imaging
- Video signal routing
- Avionics test equipment
- Cross Connects
- High speed data transmission line cards
- Automatic test equipment
- Central office
- Avionics and Military Systems
- Public switching systems
- MP3 players
