Parameters |
Factory Lead Time |
1 Week |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2010 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
10Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
842mW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Base Part Number |
MAX312 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Power Supplies |
512/+-15V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
30V |
Min Supply Voltage |
4.5V |
Nominal Supply Current |
5μA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
225 ns |
Voltage - Supply, Single/Dual (±) |
4.5V~30V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
185 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
10Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
65 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
15pF 15pF |
On-state Resistance Match-Nom |
0.3Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
225ns, 185ns |
Charge Injection |
20pC |
Channel-to-Channel Matching (ΔRon) |
300m Ω |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
275ns |
Switch-off Time-Max |
235ns |
Normal Position |
NO |
Length |
19.175mm |
Width |
7.62mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MAX312EPE+ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. This analog switch is mounted in Through Hole. 1:1 is the number of circuits in the multiplexer and demultiplexer. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 16. By its 1 channels, the electronic component provides high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. There is an electrical component included in the 16 series. A SPST - NC switching circuit is used to build these analog multiplexers. There are 4 circuits in this multiplexer. Using the MAX312 search parameter, you can discover variants of the switch. This digital multiplexer has 10Ohm internal resistance. The datasheets for the 16 pins explain the functions. In this analog multiplexer, the value is Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. The analog switch ic is of the Dual, Single supply type and is cost-effective. It is recommended to use 4.5V as the lowest voltage for the electrical part. A voltage higher than 1μA may cause damage to the switch multiplexer. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. In the case of dual power supplies, you should connect at least 4.5V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
MAX312EPE+ Features
1 Channels
Switch Circuit: SPST - NC
MAX312EPE+ Applications
There are a lot of Maxim Integrated MAX312EPE+ Analog Switches & Multiplexers ICs applications.
- Precision data acquisition
- Medical
- Power routing
- Cell phones
- Channelized and Unchannelized DS3 applications
- Sample-and-hold systems
- Optical Applications
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- HDTV
- Multiplexers