Parameters |
Factory Lead Time |
1 Week |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2003 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
10Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
842mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX312 |
Pin Count |
16 |
Operating Supply Voltage |
18V |
Polarity |
Non-Inverting |
Power Supplies |
12/+-15V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
30V |
Min Supply Voltage |
4.5V |
Nominal Supply Current |
5μA |
Max Supply Current |
500μA |
Throw Configuration |
SPST |
Turn On Delay Time |
275 ns |
Voltage - Supply, Single/Dual (±) |
9V~36V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
235 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
10Ohm |
Min Dual Supply Voltage |
4.5V |
High Level Output Current |
100mA |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
55 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
20pF 20pF |
On-state Resistance Match-Nom |
0.05Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
225ns, 185ns |
Charge Injection |
70pC |
Channel-to-Channel Matching (ΔRon) |
50m Ω |
Crosstalk |
-104dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
225ns |
Switch-off Time-Max |
185ns |
Normal Position |
NC |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MAX312FESE+ Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tube is used. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have the same number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. A total of 16 terminations have been recorded. A electrical component with 1 channels is capable of high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. The electronic part body is injected with 16 pins. These analog multiplexers are built based on SPST - NC switching circuits. A 4 circuit is present in this switch device. Search with MAX312 if you are looking for analog multiplexer variants. This digital multiplexer has 10Ohm internal resistance. You can find the functions of the 16 pins in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. normally, users should not supply switches with voltages higher than 30V. A analog switch ic that has a cost-effective Dual, Single supply type. 4.5V should be the lowest voltage fed to the electronic component. Putting voltage greater than 500μA on the multiplexer may cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. When using dual power supplies, you should attach at least 4.5V. A voltage of 18V can be used to operate the electronic component.
MAX312FESE+ Features
1 Channels
Switch Circuit: SPST - NC
MAX312FESE+ Applications
There are a lot of Maxim Integrated MAX312FESE+ Analog Switches & Multiplexers ICs applications.
- Optical Applications
- Precision instrumentation
- High reliability control systems
- New designs requiring multiplexer functions
- Automotive applications
- Communications systems
- Audio and video switching
- SONET
- CSU
- Access Concentrators