MAX313EPE+
| Parameters | |
|---|---|
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 275 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 235 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 10Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 15pF 15pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 225ns, 185ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | MAX313 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
MAX313EPE+ Overview
Shipping overseas is convenient with the electronic component packed in 16-DIP (0.300, 7.62mm). This packaging method provides high reliability because it uses advanced packaging techniques. Mounted in Through Hole is this multiplexer. Multiplexers and demultiplexers have a ratio of 1:1. Extended operating temperature around -40°C~85°C TA. There are 16 terminations totally. The electronic part provides high-quality output because it has 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. It is part of the design of the 16 series that this electronic component is included. Unlike digital switches, these are based on SPST - NO switching circuits. There are 4 circuits in this multiplexer. Try searching for MAX313 variants of the analog switch ic. This digital multiplexer has 10Ohm internal resistance. To find out what the functions of 16 pins are, please refer to their datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 30V to the switch device in normal circumstances. The analog switch ic is of the Dual, Single supply type and is cost-effective. 4.5V is the lowest voltage that should be fed to the electronic electronic part. For this switch, a dual supply voltage is feasible, but it must not exceed 20VA dual power supply should have at least 4.5V voltage attached. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. There is a voltage range of 20V operating voltages for the electrical part.
MAX313EPE+ Features
1 Channels
Switch Circuit: SPST - NO
MAX313EPE+ Applications
There are a lot of Maxim Integrated MAX313EPE+ Analog Switches & Multiplexers ICs applications.
- DVD-R
- Avionics test equipment
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Frame Relay Equipment
- Industrial and process control systems
- Industrial control systems
- Low-Voltage
- Precision instrumentation
- USB 1.1 signal switching circuits
- Optical Applications
