MAX313EUE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX313 |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 100pA |
| Max Supply Current | 100pA |
| Throw Configuration | SPST |
| Turn On Delay Time | 225 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~30V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 185 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 10Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 100mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 15pF 15pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 225ns, 185ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX313EUE+T Overview
As the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Operating temperature extended to -40°C~85°C TA. A total of 16 terminations have been recorded. A high-quality output is provided by the electrical component's 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. Into the electrical component body are injected 16 pins. These analog multiplexers are built based on SPST - NO switching circuits. A 4 circuit is present in this switch device. If you are looking for variants of the digital switch, trying search with MAX313. As far as internal resistance is concerned, it has 10Ohm. To find out what the 16 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 30V in normal situations. 4.5V should be the lowest voltage fed to the electronic component. The switch multiplexer may be damaged if it is exposed to voltage greater than 100pA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. When using dual power supplies, you should attach at least 4.5V. Operating voltages of 20V are compatible with the electrical part.
MAX313EUE+T Features
1 Channels
Switch Circuit: SPST - NO
MAX313EUE+T Applications
There are a lot of Maxim Integrated MAX313EUE+T Analog Switches & Multiplexers ICs applications.
- Modems
- Relay replacements
- ISDN NT1/TA
- CSU
- ATM
- Transmit
- SDH/SONET multiplexers
- Digital Cross-Connects
- Precision data acquisition
- DVD-R
