MAX313LCSE+T
| Parameters | |
|---|---|
| On-State Resistance (Max) | 10Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 15pF 15pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 225ns, 185ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 10Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX313 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 100pA |
| Max Supply Current | 100pA |
| Throw Configuration | SPST |
| Turn On Delay Time | 225 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 185 ns |
| Max Dual Supply Voltage | 20V |
MAX313LCSE+T Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature extended to 0°C~70°C TA. Total terminations are 16. A 1 channel electronic part produces high-quality output. Turning on and running the electrical part should be easy with a 15V voltage supply. An injection of 16 pins is performed into the body of the electrical component. The analog switch ics are built using SPST - NO switching circuits. There are 4 circuits in this multiplexer. Use MAX313 to search for variants of the digital switches. A 10Ohm internal resistance characterizes this multiplexer. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. Dual, Single supply type digital switch with a low cost. It is recommended to use 4.5V as the lowest voltage for the electrical part. The analogue multiplexer may be damaged if voltage is greater than 100pA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. You should attach at least 4.5V voltage if you are using dual power supply. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. Operating voltages range from 20V.
MAX313LCSE+T Features
1 Channels
Switch Circuit: SPST - NO
MAX313LCSE+T Applications
There are a lot of Maxim Integrated MAX313LCSE+T Analog Switches & Multiplexers ICs applications.
- Battery Powered Systems
- E1 Multiplexer
- Battery-powered systems
- Video switching
- PBX interfaces
- Switching Systems
- Cellular phones
- Channel Banks
- Access Concentrators
- Communications systems
