MAX313LCUE+T

225ns, 185ns SPST - NO 10Ohm Analog Switches BREAK-BEFORE-MAKE MAX313 16 Pins 500pA 15V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX313LCUE+T
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 474
Description: 225ns, 185ns SPST - NO 10Ohm Analog Switches BREAK-BEFORE-MAKE MAX313 16 Pins 500pA 15V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Number of Pins	16
Operating Temperature	0°C~70°C TA
Packaging	Tape & Reel (TR)
Published	2009
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	10Ohm
Terminal Finish	TIN
Subcategory	Multiplexer or Switches
Max Power Dissipation	842mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	MAX313
Output	SEPARATE OUTPUT
Pin Count	16
Operating Supply Voltage	20V
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	36V
Min Supply Voltage	4.5V
Nominal Supply Current	100pA
Max Supply Current	100pA
Throw Configuration	SPST
Turn On Delay Time	225 ns
Voltage - Supply, Single/Dual (±)	4.5V~36V ±4.5V~20V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	185 ns
Max Dual Supply Voltage	20V
On-State Resistance (Max)	10Ohm
Min Dual Supply Voltage	4.5V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	75 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	15pF 15pF
On-state Resistance Match-Nom	0.3Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	225ns, 185ns
Charge Injection	20pC
Channel-to-Channel Matching (ΔRon)	300m Ω
Crosstalk	-85dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Normal Position	NO
Height Seated (Max)	1.1mm
Length	5mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

MAX313LCUE+T Overview

The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Temperatures around 0°C~70°C TA are extended for operation. In total, there are 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. A total of 16 pins are injected into the electrical part body. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Circuits number 4 make up this analogue multiplexer. Try searching with MAX313 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 10Ohm. Please refer to the datasheets for 16 pins functions. There is a standard Multiplexer or Switches analogue multiplexer here. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. Analog switch ics with Dual, Single supply type are cost-effective. It is recommended that the electrical component receives a voltage of 4.5V. Putting voltage greater than 100pA on the multiplexer may cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. If you are using a dual power supply, you should attach at least 4.5V. There are SEPARATE OUTPUT outputs on this analog switch ic. A voltage of 20V can be used to operate the electronic component.