MAX313LEPE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Package / Case | PDIP |
| Number of Pins | 16 |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| HTS Code | 8542.39.00.01 |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 100pA |
| Max Supply Current | 100pA |
| Throw Configuration | SPST |
| Turn On Delay Time | 225 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 185 ns |
| Max Dual Supply Voltage | 20V |
| Min Dual Supply Voltage | 4.5V |
| Off-state Isolation-Nom | 75 dB |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 425ns |
| Normal Position | NO |
| Height Seated (Max) | 4.572mm |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX313LEPE+ Overview
Shipping overseas is convenient due to the electrical component's packing in PDIP. Advanced packaging method Tube is used to provide high reliability. In total, there have been 16 terminations. A high-quality output is provided by the electrical component's 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. An electrical component of this type can be found in the 16 series. This digital multiplexer has 10Ohm internal resistance. Please refer to the datasheets for 16 pins functions. Theswitch device is a typical Multiplexer or Switches. Users shouldn't supply more than 36V voltage to the switch device. Analogue multiplexer with a Dual, Single supply type that is cost-effective. A low voltage of 4.5V should be applied to the electronic component. It may damage the digital multiplexer if the voltage is higher than 100pA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. A dual power supply should have at least 4.5V voltage attached. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. 20V operating voltages can be used with this electrical part. An environment with a temperature greater than 85°C should not be used to operate the digital switches.
MAX313LEPE+ Features
1 Channels
MAX313LEPE+ Applications
There are a lot of Maxim Integrated MAX313LEPE+ Analog Switches & Multiplexers ICs applications.
- Fiber to the Home
- Fiber In The Loop (FITL)
- RGB switches
- FTTH
- E1 Network Equipment
- SONET
- Precision data acquisition
- Relay Replacement
- Data switching
- ISDN NT1/TA
