Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2009 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
10Ohm |
Terminal Finish |
MATTE TIN |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
842mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Base Part Number |
MAX313 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
JESD-30 Code |
R-PDSO-G16 |
Operating Supply Voltage |
20V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
36V |
Min Supply Voltage |
4.5V |
Nominal Supply Current |
100pA |
Max Supply Current |
100pA |
Throw Configuration |
SPST |
Turn On Delay Time |
225 ns |
Voltage - Supply, Single/Dual (±) |
4.5V~36V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
185 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
10Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
15pF 15pF |
On-state Resistance Match-Nom |
0.3Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
225ns, 185ns |
Charge Injection |
20pC |
Channel-to-Channel Matching (ΔRon) |
300m Ω |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NO |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MAX313LESE+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a number of circuits 1:1. Operational temperature extended around -40°C~85°C TA. Total terminations are 16. A high-quality output is provided by the electrical component's 1 channels. Turning on and running the electrical part should be easy with a 15V voltage supply. It is part of the design of the 16 series that this electronic component is included. Multiplexers built on a SPST - NO switching circuit are built. It consists of 4 circuits. MAX313 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 10Ohm. In this analog multiplexer, the value is Multiplexer or Switches. Users shouldn't supply more than 36V voltage to the switch device. A analog switch ic that has a cost-effective Dual, Single supply type. 4.5V is the lowest voltage that should be fed to the electronic electronic part. A digital multiplexer may suffer damage if voltage is applied above 100pA. There is no problem with using dual supply voltage, but it should not exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. This electrical part is compatible with 20V operating voltages.
MAX313LESE+T Features
1 Channels
Switch Circuit: SPST - NO
MAX313LESE+T Applications
There are a lot of Maxim Integrated MAX313LESE+T Analog Switches & Multiplexers ICs applications.
- DSLAMs
- Battery Powered Instruments
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Microwave transmission systems
- Avionics
- Avionics test equipment
- Audio and video signal routing
- Battery Powered Systems
- Digital access cross connects
- PCMCIA cards