banner_page

MAX313MJE

16 Terminations16 Pin Signal switch4 FunctionsMin 4.5V VMax 30V V


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX313MJE
  • Package: CDIP
  • Datasheet: -
  • Stock: 840
  • Description: 16 Terminations16 Pin Signal switch4 FunctionsMin 4.5V VMax 30V V(Kg)

Details

Tags

Parameters
Package / Case CDIP
Surface Mount NO
Number of Pins 16
Packaging Tube
Published 2010
JESD-609 Code e0
Pbfree Code no
Part Status Active
Moisture Sensitivity Level (MSL) 1
Number of Terminations 16
ECCN Code EAR99
Resistance 10Ohm
Terminal Finish Tin/Lead (Sn/Pb)
HTS Code 8542.39.00.01
Subcategory Multiplexer or Switches
Max Power Dissipation 842mW
Technology CMOS
Terminal Position DUAL
Terminal Form THROUGH-HOLE
Peak Reflow Temperature (Cel) 240
Number of Functions 4
Supply Voltage 15V
Terminal Pitch 2.54mm
Time@Peak Reflow Temperature-Max (s) 20
Output SEPARATE OUTPUT
Pin Count 16
Operating Temperature (Max) 125°C
Operating Temperature (Min) -55°C
Operating Supply Voltage 20V
Power Supplies 512/+-15V
Temperature Grade MILITARY
Number of Channels 1
Max Supply Voltage 30V
Min Supply Voltage 4.5V
Analog IC - Other Type SPST
Nominal Supply Current 100pA
Max Supply Current 100pA
Turn On Delay Time 225 ns
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 185 ns
Max Dual Supply Voltage 20V
Min Dual Supply Voltage 4.5V
Off-state Isolation-Nom 65 dB
On-state Resistance Match-Nom 0.3Ohm
Switching BREAK-BEFORE-MAKE
Switch-on Time-Max 275ns
Switch-off Time-Max 235ns
Normal Position NC
Height Seated (Max) 5.08mm
Width 7.62mm
Radiation Hardening No
RoHS Status RoHS Compliant

MAX313MJE Overview


Due to the lack of space on the board, digital switch is provided in the CDIP.Tube is the method used for packaging.As part of its basic configuration, 16 terminations are designed as a part of it.In this case, 15V is the voltage supplied to the multiplexer's system.Signal switch has 16 component pins.At the end of a conductor, it uses THROUGH-HOLE as the point where the conductor ends.It is configured with 16 pins.Normally, 512/+-15V is powered by a battery.Part number Multiplexer or Switches indicates that the digital switch ic is an electronic part.If the supply voltage is set to 20V, reliable performance of the multiplexers can be achieved.A resistance of 10Ohm is used to operate the signal switching.Transmission is carried out over 1 channels in the turn signal switch's circuit.The device is specified to operate at a maximum supply voltage of 30V in accordance with the applicable device specification.A minimum supply voltage of 4.5V is required to operate the digital swith.In this case, 125°C is the maximum operating temperature of the switches.In this digital switch, the analog integrated circuit is SPST.

MAX313MJE Features


Supplied in the CDIP package
Power supplies of 512/+-15V
Operating with the supply voltage of 20V
SPST as the analog IC

MAX313MJE Applications


There are a lot of Maxim Integrated MAX313MJE Signal Switches / Multiplexers / Decoders applications.

  • High-performance memory-decoding applications
  • Data demultiplexing
  • To select different devices in microprocessor output
  • Microprocessor input/output systems
  • Paper plants
  • CNC machines
  • Automatic health monitoring systems
  • Enabling block of memory depending on address in memory chips
  • Enabling different functions units in microprocessor instruction decoding
  • Relay

Write a review

Note: HTML is not translated!
    Bad           Good