MAX314EPE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX314 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 225 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 185 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 10Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 15pF 15pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 225ns, 185ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 275ns |
| Switch-off Time-Max | 235ns |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX314EPE+ Overview
Presented in 16-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. The advanced packaging method Tube provides high reliability. It is mounted in the position Through Hole. Multiplexer and demultiplexer circuits have a number 1:1. Operational temperature extended around -40°C~85°C TA. In total, 16 terminations have occurred. A electrical component with 1 channels is capable of high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. An electrical component like this is included in the 16 series. On the other hand, analog switches can be constructed using SPST - NO/NC switching circuits. A 4 circuit is present in this switch device. Try searching for MAX314 variants of the analog switch ic. There is 10Ohm internal resistance in this digital multiplexer. The functions of 16 pins can be found in the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. Users shouldn't supply more than 20V voltage to the switch device. The digital multiplexer has a low cost Dual, Single supply. It is recommended to use 4.5V as the lowest voltage for the electrical part. Put voltage above 1μA on the multiplexer to cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. The voltage should be at least 4.5V if you are using dual power supplies. SEPARATE OUTPUT outputs are utilized by this digital multiplexer.
MAX314EPE+ Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX314EPE+ Applications
There are a lot of Maxim Integrated MAX314EPE+ Analog Switches & Multiplexers ICs applications.
- SDH
- Remote wireless modules
- ISDN NT1/TA
- Industrial and process control systems
- Cellular phones
- Frame Relay Equipment
- Relay replacements
- Cable PC
- PBXs
- Precision data acquisition
