MAX314FESE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | TIN |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX314 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 275 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 235 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 10Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 20pF 20pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 225ns, 185ns |
| Charge Injection | 70pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -104dB @ 1MHz |
| Switch-on Time-Max | 225ns |
| Switch-off Time-Max | 185ns |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX314FESE+T Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operational temperature extended around -40°C~85°C TA. In total, there are 16 terminations. The electronic part provides high-quality output because it has 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. There are 16 pins injected into the electronic part body. A SPST - NO/NC switching circuit is used for these analog switches. A total of 4 circuits make up this switch device. Look for analog switch ic variants by searching with MAX314. There is 10Ohm internal resistance in this digital multiplexer. normally, users should not supply switches with voltages higher than 30V. It is recommended to use 4.5V as the lowest voltage for the electrical part. If you put voltage higher than 500μA on the digital multiplexer, damage may occur. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. A voltage of 20V can be used to operate the electronic component.
MAX314FESE+T Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX314FESE+T Applications
There are a lot of Maxim Integrated MAX314FESE+T Analog Switches & Multiplexers ICs applications.
- Audio and video switching
- Multi-Line E1 Interface Cards
- Automatic test equipment
- Cable Modem
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Optical Applications
- Cellular phones
- SONET/SDH ADM
- Digital cross connects (DSX-1)
- Communication systems
