Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2009 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
10Ohm |
Terminal Finish |
TIN |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
842mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Base Part Number |
MAX314 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
JESD-30 Code |
R-PDSO-G16 |
Operating Supply Voltage |
18V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
30V |
Min Supply Voltage |
4.5V |
Nominal Supply Current |
5μA |
Max Supply Current |
200μA |
Throw Configuration |
SPST |
Turn On Delay Time |
275 ns |
Voltage - Supply, Single/Dual (±) |
4.5V~36V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
235 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
10Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
15pF 15pF |
On-state Resistance Match-Nom |
0.3Ohm |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
225ns, 185ns |
Charge Injection |
20pC |
Channel-to-Channel Matching (ΔRon) |
300m Ω |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
225ns |
Switch-off Time-Max |
185ns |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MAX314LCSE+T Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Extended operating temperature around 0°C~70°C TA. In total, 16 terminations have occurred. By its 1 channels, the electronic component provides high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. This electronic part can be found in the 16 series. The analog switch ics are built using SPST - NO/NC switching circuits. 4 circuits are used in this analogue multiplexer. Try searching with MAX314 if you're looking for variants. As far as internal resistance is concerned, it has 10Ohm. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 30V. The digital multiplexer has a low cost Dual, Single supply. In order for the electronic part to function properly, the lowest voltage should be 4.5V. If you put voltage higher than 200μA on the digital multiplexer, damage may occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. With dual power supplies, you should attach at least 4.5V. There are SEPARATE OUTPUT outputs on this analog switch ic. This electrical part is compatible with 18V operating voltages.
MAX314LCSE+T Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX314LCSE+T Applications
There are a lot of Maxim Integrated MAX314LCSE+T Analog Switches & Multiplexers ICs applications.
- Power routing
- Transmit
- Intelligent PBX
- CSU
- Digital access cross connects
- Signal routing between systems
- Battery-powered systems
- Audio signal routing
- DVD-R
- Video signal routing