MAX314LESE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 10Ohm |
| Terminal Finish | TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX314 |
| Pin Count | 16 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 10Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 100mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 15pF 15pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 225ns, 185ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 225ns |
| Switch-off Time-Max | 185ns |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX314LESE+T Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Operating temperature extended to -40°C~85°C TA. There are 16 terminations totally. High-quality output is provided by the electronic component's 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. An electrical component of this type can be found in the 16 series. The analog switch ics are built using SPST - NO/NC switching circuits. Circuits number 4 make up this analogue multiplexer. MAX314 can be used to search for analog multiplexer variants. In this multiplexer, the internal resistance is 10Ohm. The datasheets for the 16 pins explain the functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 36V. It is recommended that the electrical component receives a voltage of 4.5V. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. The voltage should be at least 4.5V if you are using dual power supplies.
MAX314LESE+T Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX314LESE+T Applications
There are a lot of Maxim Integrated MAX314LESE+T Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- Battery-powered systems
- Audio and video signal routing
- High-Voltage
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Automotive applications
- Digital Cross-Connects
- Signal routing between systems
- PCMCIA cards
- Imaging
