MAX3160EAP+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 453.59237mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Subcategory | Line Driver or Receivers |
| Technology | BICMOS |
| Voltage - Supply | 3V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX3160 |
| Pin Count | 20 |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Interface | RS-232, RS-422, RS-485 |
| Operating Supply Current | 2.5mA |
| Nominal Supply Current | 2.5mA |
| Propagation Delay | 150 ns |
| Data Rate | 10Mbps |
| Differential Output | YES |
| Protocol | RS232, RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 2/2 |
| Driver Number of Bits | 2 |
| Receiver Number of Bits | 2 |
| Duplex | Full |
| Receiver Hysteresis | 500mV |
| ESD Protection | No |
| Simplex/Duplex | Full Duplex |
| Transmit Delay-Max | 800 ns |
| Max Junction Temperature (Tj) | 150°C |
| Number of Transmitters | 2 |
| Height | 1.99mm |
| Length | 7.33mm |
| Width | 5.38mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX3160EAP+ Overview
LED drivers benefit from this IC's enhanced 20-SSOP (0.209, 5.30mm Width) package.This receiver is mounted in the Tube package.It has proved to be a valuable component for a variety of applications since it is a Transceiver can transceiver.Any Surface Mount-type PCB or development board can be used with this wide receiver.A differential driver like this uses 3V~5.5V of power.At any one time, this electronic part can have up to 2/2 eligible receivers/drivers.In most applications, this ic receiver is used in environments where -40°C~85°C is the operating temperature.There is a voltage range of 3.3V for this line driver ic, so it can operate efficiently.In this package, you will find 20 market-standard pinouts for this transceiver.Since the base part number MAX3160 describes the product type, temperature, package, etc., you might get more options by searching with it.Wide receiver with enhanced power dissipation control, 20-pin.A combination of optical transceiver downsizing and high-density Surface Mount mounting reduces the package size dramatically.In terms of resolution, this ic receiver was capable of providing a 2-bit resolution.Typically, the resolution of this receiver is specified to be 2 bits.A Line Driver or Receivers subcategory can be assigned to this rf transceiver module.Driver ICs such as this one are designed to operate from 3.3/5V power sources.Using the input voltage of 2.5mA, this integrating circuit is capable of driving LEDs with an output voltage of 12 volts.An antenna transmits or sends data through 2 transmitters, which are can transceivers used to transmit radio waves to send data.As a result of the embedded architecture of this optical transceiver, there are 1 channels in total.
MAX3160EAP+ Features
Tube package
20 pin count
20 pins
3.3/5V power supply
1 channels
MAX3160EAP+ Applications
There are a lot of Maxim Integrated MAX3160EAP+ Drivers/Receivers/Transceivers applications.
- Fiber optic cable connection network
- TV signal transmission
- Routers
- Carrier phase observations
- Interconnection between switches and computers
- Low power, low voltage systems
- interconnection between computers
- Fiber distributed data interface (FDDI)
- Notebook
- AV receiver
