MAX317CPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX317 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 5μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 145 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 175 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX317CPA+ Overview
The electronic component is convenient to ship overseas because it is packed in a 8-DIP (0.300, 7.62mm). This high-reliability packaging method uses advanced packaging methods Tube. This analog switch is mounted in Through Hole. 1:1 is the number of circuits in the multiplexer and demultiplexer. The operating temperature is extended to around 0°C~70°C TA. In total, there are 8 terminations. This electronic part offers high-quality output due to its 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. The electronic part body is injected with 8 pins. Unlike digital switches, these are based on SPST - NC switching circuits. The circuits in this analogue multiplexer number 1. Try searching for the analog switch ic with MAX317 if you are looking for variants. There is 35Ohm internal resistance in this digital multiplexer. The datasheets for the 8 pins explain the functions. Multiplexer or Switches is a typical switch device. It is generally not recommended to supply a voltage higher than 30V to the switch device in normal circumstances. Dual, Single supply type digital switch with a low cost. It is recommended to use 10V as the lowest voltage for the electrical part. For this digital switch to work, 1μA current would suffice. The analogue multiplexer may be damaged if voltage is greater than 1μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. In the case of dual power supplies, you should connect at least 4.5V. Operating voltages range from 20V.
MAX317CPA+ Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX317CPA+ Applications
There are a lot of Maxim Integrated MAX317CPA+ Analog Switches & Multiplexers ICs applications.
- Audio/video switches
- Transmit
- Automatic test equipment
- Industrial
- Fault Tolerant Systems
- Signal routing between systems
- High-Voltage
- HDTV
- SONET
- Central office
