Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-SOIC (0.154, 3.90mm Width) |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tape & Reel (TR) |
Published |
1995 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
35Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
727mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
15V |
Base Part Number |
MAX317 |
Pin Count |
8 |
JESD-30 Code |
R-PDSO-G8 |
Operating Supply Voltage |
20V |
Number of Channels |
1 |
Number of Circuits |
1 |
Max Supply Voltage |
30V |
Min Supply Voltage |
10V |
Operating Supply Current |
1μA |
Nominal Supply Current |
5μA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
145 ns |
Voltage - Supply, Single/Dual (±) |
10V~30V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
175 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
8pF 8pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
175ns, 145ns |
Charge Injection |
3pC |
Channel-to-Channel Matching (ΔRon) |
2 Ω (Max) |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NC |
Length |
4.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MAX317CSA+T Overview
The electronic component is convenient to ship overseas because it is packed in a 8-SOIC (0.154, 3.90mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Temperatures around 0°C~70°C TA are extended for operation. There are 8 terminations totally. The electronic part delivers high-quality output through its 1 channels. Turning on and running the electrical part should be easy with a 15V voltage supply. As part of its design, the 8 series is equipped with this electronic component. Unlike digital switches, these are based on SPST - NC switching circuits. This multiplexer is composed of 1 circuits. Search with MAX317 if you are looking for analog multiplexer variants. As far as internal resistance is concerned, it has 35Ohm. In this analog multiplexer, the value is Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. Dual, Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 10V. For this digital switch to work, 1μA current would suffice. Putting voltage greater than 1μA on the multiplexer may cause damage. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply. A voltage of 20V can be used to operate the electronic component.
MAX317CSA+T Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX317CSA+T Applications
There are a lot of Maxim Integrated MAX317CSA+T Analog Switches & Multiplexers ICs applications.
- E1 Network Equipment
- Imaging
- Video signal routing
- Transmit
- Cross Connects
- Communications systems
- New designs requiring multiplexer functions
- ATM
- Automotive applications
- Multi-Line E1 Interface Cards