MAX317EPA
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX317 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 5μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 145 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 175 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX317EPA Overview
Shipping overseas is convenient due to the electrical component's packing in 8-DIP (0.300, 7.62mm). High reliability is achieved by using advanced packaging method Tube. The multiplexer is located in Through Hole. 1:1 is the ratio between multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. There are 8 terminations totally. Due to its 1 channels, the electrical component produces high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. An injection of 8 pins is performed into the body of the electrical component. A SPST - NC switching circuit is used to build these analog multiplexers. A total of 1 circuits make up this switch device. Look for analog switch ic variants by searching with MAX317. Analog switches have 35Ohm internal resistance. The functions of 8 pins can be found in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Users shouldn't supply more than 30V voltage to the switch device. The analog switch ic is of the Dual, Single supply type and is cost-effective. 10V is the lowest voltage that should be fed to the electronic electronic part. For this multiplexer to operate, 1μA current would be sufficient. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. If you are using a dual power supply, you should attach at least 4.5V. Operating voltages of 20V are compatible with the electrical part.
MAX317EPA Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX317EPA Applications
There are a lot of Maxim Integrated MAX317EPA Analog Switches & Multiplexers ICs applications.
- Communication systems
- Power routing
- Battery-powered systems
- Communications systems
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- SDH
- Central office
- Audio and video routing
- Industrial control systems
- Industrial
