MAX318CPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX318 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 100pA |
| Max Supply Current | 100pA |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX318CPA+ Overview
The electrical component comes in 8-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. The advanced packaging method Tube provides high reliability. Through Hole is where this multiplexer is located. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operation at a temperature around 0°C~70°C TA. Totally, there are 8 terminations. The electronic part provides high-quality output because it has 1 channels. A 15V voltage supply should turn on and run the electronic component. Into the electrical component body are injected 8 pins. A SPST - NO switching circuit is used to build these analog multiplexers. MAX318 can be used to search for analog multiplexer variants. This digital multiplexer has 35Ohm internal resistance. To find out what the 8 pins do, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 30V volts for the multiplexer. Analog switch ics with Dual, Single supply type are cost-effective. 10V should be the lowest voltage fed to the electronic component. The analogue multiplexer could operate on 1μA current. When the digital multiplexer is charged above 100pA, damage can occur. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. With dual power supplies, you should attach at least 4.5V. A voltage of 20V can be used to operate the electronic component.
MAX318CPA+ Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX318CPA+ Applications
There are a lot of Maxim Integrated MAX318CPA+ Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- Low-Voltage
- Multi-Line E1 Interface Cards
- USB 1.1 signal switching circuits
- PBX interfaces
- Avionics
- High reliability control systems
- 65 V DACs
- Frame Relay Equipment
- Mechanical reed relay replacement
