MAX318EPA
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX318 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Current-Max (Isup) | 0.005mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX318EPA Overview
The electronic component is convenient to ship overseas because it is packed in a 8-DIP (0.300, 7.62mm). This packaging method provides high reliability because it uses advanced packaging techniques. A switch device like this is mounted in Through Hole. 1:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. 8 terminations have been made so far. High-quality output is provided by the electronic component's 1 channels. A 15V voltage supply should turn on and run the electronic component. There is an electrical component included in the 8 series. A SPST - NO switching circuit is used for these analog switches. The multiplexer consists of 1 circuits. MAX318 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 35Ohm. For functions related to 8 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 30V should not normally be supplied to the switches. 10V is the lowest voltage that should be fed to the electronic electronic part. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. In the case of dual power supplies, you should connect at least 4.5V.
MAX318EPA Features
1 Channels
Switch Circuit: SPST - NO
MAX318EPA Applications
There are a lot of Maxim Integrated MAX318EPA Analog Switches & Multiplexers ICs applications.
- PDAs
- Digital Cross-Connects
- Communication systems
- SONET/SDH ADM
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Audio and video routing
- Avionics and Military Systems
- PCMCIA cards
- High reliability control systems
- Precision test equipment
