MAX319CPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX319 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 100pA |
| Max Supply Current | 100pA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 35Ohm |
| Height | 4.45mm |
| Length | 9.91mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX319CPA+ Overview
This electronic part is conveniently packaged in 8-DIP (0.300, 7.62mm), making it easy to ship abroad. This high-reliability packaging method uses advanced packaging methods Tube. Through Hole is where this multiplexer is located. Multiplexers and demultiplexers have a number of circuits 2:1. The operating temperature is extended to around 0°C~70°C TA. There are 8 terminations totally. A 1 channel electronic part produces high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. It is injected into the electrical part body with 8 pins. These analog multiplexers are built based on SPDT switching circuits. Try searching with MAX319 if you're looking for variants. An switch multiplexer with 35Ohm internal resistance has a value of 35Ohm. The functions of 8 pins can be found in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 30V volts for the multiplexer. Digital switch that provides Dual, Single power at a cost-effective price. It is recommended to use 10V as the lowest voltage for the electrical part. 1μA current would be enough for this multiplexer to operate. A voltage higher than 100pA may cause damage to the switch multiplexer. There is no problem with using dual supply voltage, but it should not exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply. There is a voltage range of 20V operating voltages for the electrical part. Drain to Source resistance for this electronic component is 35Ohm.
MAX319CPA+ Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
Drain-to-Source resistance: 35Ohm
MAX319CPA+ Applications
There are a lot of Maxim Integrated MAX319CPA+ Analog Switches & Multiplexers ICs applications.
- Ultrasound
- Cable Modem
- Voice over IP/DSL – Integrated Access Devices, Smart
- CSU
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Relay replacements
- Fiber to the Home
- Channelized and Unchannelized DS3 applications
- Imaging
- Medical Instrumentation
