MAX319CSA
| Parameters | |
|---|---|
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | MAX319 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 100pA |
| Max Supply Current | 100pA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
MAX319CSA Overview
This electronic part is conveniently packaged in 8-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. To ensure high reliability, a new packaging method Tube is used. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Operation at a temperature around 0°C~70°C TA. A total of 8 terminations have been recorded. A electrical component with 1 channels is capable of high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. A key feature of the 8 series is the inclusion of this electronic part as part of its design. A SPDT switching circuit is used to build these analog multiplexers. Try searching for MAX319 variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 35Ohm. For functions related to 8 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. Users shouldn't supply more than 30V voltage to the switch device. The analog switch ic is of the Dual, Single supply type and is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 10V. 1μA current would be enough for this multiplexer to operate. Put voltage above 100pA on the multiplexer to cause damage. There is no problem with using dual supply voltage, but it should not exceed 20V. With dual power supplies, you should attach at least 4.5V. The electronic component can function from 20V.
MAX319CSA Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX319CSA Applications
There are a lot of Maxim Integrated MAX319CSA Analog Switches & Multiplexers ICs applications.
- MP3 players
- SDH/SONET multiplexers
- Fiber In The Loop (FITL)
- Audio signal routing
- High-Voltage
- Remote wireless modules
- Communication systems
- Cable PC
- Video switching
- Audio and video signal routing
