MAX319CSA+T
| Parameters | |
|---|---|
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | MAX319 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 100pA |
| Max Supply Current | 100pA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
MAX319CSA+T Overview
The electrical component comes in 8-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. High reliability is ensured by the advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Around 0°C~70°C TA is the extended operating temperature. Total terminations are 8. A electrical component with 1 channels is capable of high-quality output. A 15V voltage supply should turn on and run the electronic component. 8 pins are injected to the electronic part body. A SPDT switching circuit is used to build these analog multiplexers. This multiplexer is composed of 1 circuits. If you are looking for variants of the digital switch, trying search with MAX319. A 35Ohm internal resistance characterizes this multiplexer. To find out what the 8 pins do, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 30V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 10V is the lowest voltage the electrical component should receive. In order to operate this switch device, it would need a current of 1μA. The analogue multiplexer may be damaged if voltage is greater than 100pA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. A dual power supply should have at least 4.5V voltage attached. Operating voltages range from 20V.
MAX319CSA+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX319CSA+T Applications
There are a lot of Maxim Integrated MAX319CSA+T Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- Avionics
- Modems
- Remote Powered Equipment
- Medical
- High reliability control systems
- Battery-powered systems
- Medical Instrumentation
- SONET
- Communications systems
