MAX319EPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX319 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 5μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 145 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 175 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX319EPA+ Overview
This electronic part is conveniently packaged in 8-DIP (0.300, 7.62mm), making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tube. The multiplexer is located in Through Hole. Multiplexer and demultiplexer circuits have a number 2:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 8. By its 1 channels, the electronic component provides high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. This electronic part can be found in the 8 series. A SPDT switching circuit is used to build these analog multiplexers. A 1 circuit is present in this switch device. Use MAX319 to search for variants of the digital switches. This digital multiplexer has 35Ohm internal resistance. The functions of 8 pins can be found in the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 30V to the switch device in normal circumstances. An effective Dual, Single supply digital multiplexer. In order for the electronic part to function properly, the lowest voltage should be 10V. In order to operate this switch device, it would need a current of 1μA. It may damage the digital multiplexer if the voltage is higher than 1μA. Despite this switch's dual supply capability, its voltage should not exceed 20V. In the case of dual power supplies, you should connect at least 4.5V. 20V operating voltages are supported by the electronic component.
MAX319EPA+ Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX319EPA+ Applications
There are a lot of Maxim Integrated MAX319EPA+ Analog Switches & Multiplexers ICs applications.
- Ultrasound
- E1 Network Equipment
- DSUs
- Avionics test equipment
- Routers
- Intelligent PBX
- Signal routing between systems
- Channel Banks
- Power routing
- PDH Multiplexers
