MAX319ESA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | MAX319 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Voltage | 25V |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 100pA |
| Max Supply Current | 100pA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 35Ohm |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX319ESA+ Overview
Packed in 8-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Tube. Multiplexers like this are mounted in the Surface Mount position. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. Totally, there are 8 terminations. The electronic part provides high-quality output because it has 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. It is injected into the electrical part body with 8 pins. The analog switch ics are built using SPDT switching circuits. Search with MAX319 if you are looking for analog multiplexer variants. The internal resistance of this digital multiplexer is 35Ohm. You can find the functions of the 8 pins in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. An abnormal situation would be for the switch device to be supplied with a voltage greater than 30V. An effective Dual, Single supply digital multiplexer. A low voltage of 10V should be applied to the electronic component. This multiplexer would work with 1μA current. A voltage higher than 100pA may cause damage to the switch multiplexer. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. When using dual power supplies, you should attach at least 4.5V. Operating voltages range from 20V. There is 35Ohm resistance between Drain and Source for this electronic part.
MAX319ESA+ Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
Drain-to-Source resistance: 35Ohm
MAX319ESA+ Applications
There are a lot of Maxim Integrated MAX319ESA+ Analog Switches & Multiplexers ICs applications.
- Wireless Local Loop
- Precision data acquisition
- PDH Multiplexers
- PBX interfaces
- Mechanical reed relay replacement
- Multiplexers
- CSU
- SDH
- Private Branch Exchange (PBX)
- Data Acquisition Systems
