MAX319MJA
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Through Hole |
| Package / Case | CDIP |
| Number of Pins | 8 |
| Published | 1995 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 30Ohm |
| Terminal Finish | TIN/LEAD (SN/PB) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 8 |
| Temperature Grade | MILITARY |
| Number of Channels | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Analog IC - Other Type | SPDT |
| Max Supply Current | 1μA |
| Turn On Delay Time | 175 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Off-state Isolation-Nom | 68 dB |
| On-state Resistance Match-Nom | 2Ohm |
| Switching | BREAK-BEFORE-MAKE |
| Height | 3.56mm |
| Length | 10.29mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX319MJA Overview
Presented in CDIP, this electrical component is convenient for overseas shipping. There are 8 terminations totally. The electronic part provides high-quality output because it has 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. It is part of the design of the 8 series that this electronic component is included. An switch multiplexer with 30Ohm internal resistance has a value of 30Ohm. Datasheets for 8 pin functions are available upon request. It is a typical Multiplexer or Switches analog multiplexer. Multiplexers should not be powered above 30V in normal situations. A analog switch ic that has a cost-effective Dual, Single supply type. 10V should be the lowest voltage fed to the electronic component. It may damage the digital multiplexer if the voltage is higher than 1μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. You should attach at least 4.5V voltage if you are using dual power supply. With a SPDT analog IC integrated into the board. The switches should not operate in an environment where the temperature is higher than 125°C.
MAX319MJA Features
1 Channels
MAX319MJA Applications
There are a lot of Maxim Integrated MAX319MJA Analog Switches & Multiplexers ICs applications.
- PCMCIA cards
- Avionics and Military Systems
- CSU
- Cell phones
- SDH/SONET multiplexers
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Routers
- Digital cross connects (DSX-1)
- Residential Gateways, Home Gateway/Router
- Medical systems
