MAX320CPA+

150ns, 100ns SPST - NO 35Ohm Analog Switches BREAK-BEFORE-MAKE MAX320 8 Pins 100pA 5V 8-DIP (0.300, 7.62mm)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX320CPA+
Package: 8-DIP (0.300, 7.62mm)
Datasheet: PDF
Stock: 814
Description: 150ns, 100ns SPST - NO 35Ohm Analog Switches BREAK-BEFORE-MAKE MAX320 8 Pins 100pA 5V 8-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Through Hole
Mounting Type	Through Hole
Package / Case	8-DIP (0.300, 7.62mm)
Number of Pins	8
Operating Temperature	0°C~70°C TA
Packaging	Tube
Published	1995
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
ECCN Code	EAR99
Resistance	35Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	471mW
Technology	CMOS
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	5V
Base Part Number	MAX320
Output	SEPARATE OUTPUT
Pin Count	8
Operating Supply Voltage	8V
Number of Channels	1
Number of Circuits	2
Operating Supply Current	1μA
Nominal Supply Current	200μA
Max Supply Current	125μA
Throw Configuration	SPST
Turn On Delay Time	175 ns
Supply Type	Dual
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	150 ns
Max Dual Supply Voltage	8V
On-State Resistance (Max)	35Ohm
Min Dual Supply Voltage	2.7V
Dual Supply Voltage	5V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	72 dB
Current - Leakage (IS(off)) (Max)	100pA
Channel Capacitance (CS(off), CD(off))	9pF 9pF
On-state Resistance Match-Nom	0.3Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	150ns, 100ns
Charge Injection	2pC
Channel-to-Channel Matching (ΔRon)	300m Ω
Crosstalk	-85dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-off Time-Max	100ns
Normal Position	NO
Voltage - Supply, Dual (V±)	±2.7V~8V
Height	4.45mm
Length	9.91mm
Width	7.87mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

MAX320CPA+ Overview

Packed in 8-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Through Hole position. 1:1 is the number of circuits in the multiplexer and demultiplexer. Around 0°C~70°C TA is the extended operating temperature. 8 terminations have been made so far. The electronic part delivers high-quality output through its 1 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. Electronic part bodies are injected with 8 pins. These analog multiplexers are built based on SPST - NO switching circuits. 2 circuits are used in this analogue multiplexer. Try searching for MAX320 variants of the analog switch ic. An switch multiplexer with 35Ohm internal resistance has a value of 35Ohm. Datasheets for 8 pin functions are available upon request. It is a typical Multiplexer or Switches analog multiplexer. A cost-effective Dual supply type analogue multiplexer. In order to operate this switch device, it would need a current of 1μA. It may damage the digital multiplexer if the voltage is higher than 125μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 8V. A dual power supply should have at least 2.7V voltage attached. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. 8V operating voltages can be used with this electrical part.